Raspberry Pi - SPI-AD-DA-& I2C 1-Wire Board

  

                                                        

 

 

 

Support Raspberry Pi-V2 P5 , got extra 4 GPIO 28,29,30,31

The 1-Wire port is based around a DS2482-100 I2C to 1-Wire bridge device. The DS2482-100 provides bi-directional protocol conversion between the I2C port on the Raspberry Pi and any attached 1-WireŽ slave devices. An ESD Protection Diode is used to protect the Board and Raspberry Pi from electrostatic spikes on the 1-Wire port. Connections to the 1-Wire port can be made through pin on the PCB. 

                                                  

1. J2 J3  Step motor connector J2 (5V,D0,D1,D2,D3)  J3(5V,D4,D5,D6,D7) 

      can use Step motor (28BYJ-48 5VDC)48 5VDC)48 5VDC)48 5VDC)8 5VDC)

2. J20   5V,GND, D0, D1,D2,D3,D4,D5,D6,D7   OUTPUT

3. U5 ULN2803 8 darlington transistor array

4. J17  RS-Pi-V2 GPIO output      

5. J19  i2c output (GND,5V,SDA,SCL)

6.  JP4 choose 5V input from Mini USB Port J7 or RS-Pi 5V

7. J7  Mini USB 5V input

8. U6 MCP3002 SPI Interface  10 bit Analog-to-Digital Converter 

     output   J11  (Vcc, AD0, GND, AD1)       MCP3002 Data Sheet

9. U11 MCP4802  SPI Interface 8 bit Digital-to-Analog Converter   

      or U11 MCP4812 SPI Interface 10 bit Digital-to-Analog Converter   

      or  U11 MCP4822 SPI Interface 12 bit Digital-to-Analog Converter   

      output JP1 (DA0,GND,DA1,GND)            MCP4802 Data Sheet

You can choose 8 bit , 10bit or 12 bit  DAC ,

10. U15 DS2482-100 I2C to 1-Wire bridge device      DS2482-100  Data Sheet

     J22 1-wire Port pin 1 - pin4 

     (5V,GND, OW (1-Wire Data, ESD Protected). RT (1-Wire Return/Ground ,ESC protected)

11. U16 DS9503P ESD protection diode

12. D8,D9, D10, D11  GPIO 28,29,30.31 output LED

                              

    U5 uln2803  use  RS-Pi  pin 11,12,13,15,16,18,22,7 as GPIO 0 to GPIO7

 

 

                                                            MCP3002 use 10k ohm Trimpot  for INPUT DEMO

 

                                                             MCP4802 OUTPUT  DEMO

 

  

  You also can use gertboard program atod & dtoa  in this board

 

 

    18  -> DS2482-100    I2C  1-Wire  bridge chip

   /28.7E1CC8030000    -  Connect   &  Detect  DALLAS 18B20P   TEMP Sensor

     

 /28.7E1CC8030000    -  Connect   &  Detect  DALLAS 18B20P   TEMP Sensor

cat temperature   --    22.312    &  32.125

 

 

Test Program download

SPI AD/DA.c           mcp4802.c  

 

 1step.py    for 1 Step Motor on J2 

 2step.py for 2 Step Motor on J2 J3

 2step-v2.py for Rs-Pi V2 2 Step Motor on J2 J3             

 

 

Package Content

  1x Rs-Pi 2803-AD-DA - i2c-1-Wire board

1x 2x4 (8P)2.54mm pitch header for Raspberry Pi  P5 connector

1x manual 

  

 
 
 

Raspberry Pi

iPad  iPhone

Products  

 

 

Copyright ?009
www.pridopia.co.uk
All rights reserved

Home           About us           Support           Shopping           Contacts            FAQ